Mashe Posted September 21, 2021 Share Posted September 21, 2021 A pocos meses de la actualización 2.3.0, llega esta nueva versión para los dispositivos Headrush. No trae nuevos efectos o equipos, solo nuevas prestaciones y cambios. Changes Since Firmware Version 2.3.0 • Setlists can now be freely exported and imported between the HeadRush Pedalboard, Gigboard, and MX5 (Note: the Song View feature is still only available on the HeadRush Pedalboard). • The burn-in protection feature for footswitch OLED displays is now enabled after 60 minutes (was 30 minutes). • Bug Fixes: o Resolved an issue where the footswitch mode setting (Stomp, Rig, etc.) would not be retained between power cycles. o Resolved an issue where two footswitches were unable to be pressed at the same time. o Resolved an issue where a Scene LED would be incorrectly lit when loading a rig if the rig was previously saved with a scene enabled and then saved again with the scene disabled. o Resolved an issue where Scenes were occasionally not functioning correctly after importing a rig to a different type of HeadRush device (e.g., Gigboard to Pedalboard). o Resolved an issue where Ambiverb was still audible if a volume pedal was before it and set to 0%. o Resolved an issue where Pedalboard would sometimes freeze on power off. o Resolved an issue where Hands-Free mode would not update correctly if it was accessed while on the Hardware Assign page after changing an assignment. o Resolved an issue where Footswitches 9-11 would not stay lit in Rig mode. o Resolved an issue where footswitch OLED displays would sometimes go blank when entering the Looper. • Known Issues: o Very Rare: Immediately after updating, Pedalboard may get stuck on the “Loading...” screen. To resolve this, reboot the unit by holding the power button or disconnecting/reconnecting the power cable from the Pedalboard, and then re starting the unit. If this happ ens, it will only happen once, and no user data will be lost. o Very Rare: After power on, the initial rig loaded may be missing its IR. To resolve this, reboot Pedalboard and reload the rig, or reselect the IR on the IR block’s detail edit page. No user data will be lost. Quote Link to comment Share on other sites More sharing options...
rockdriguez Posted September 21, 2021 Share Posted September 21, 2021 Gracias! Quote Link to comment Share on other sites More sharing options...
Mashe Posted September 21, 2021 Author Share Posted September 21, 2021 De nada fiera. Los Jeadrusheros somos así, pura generosidad 2 Quote Link to comment Share on other sites More sharing options...
Pablo Posted September 21, 2021 Share Posted September 21, 2021 para la MX5 agrega el OCD v2, que aparecia listado en la web pero no en la propia pedalera. 2 Quote Link to comment Share on other sites More sharing options...
NICOMORDOR Posted September 21, 2021 Share Posted September 21, 2021 hace 1 hora, Pablo dijo: para la MX5 agrega el OCD v2, que aparecia listado en la web pero no en la propia pedalera. ni me habia dado cuenta que faltaba, al cabo que ni queria jajaja Quote Link to comment Share on other sites More sharing options...
NICOMORDOR Posted September 21, 2021 Share Posted September 21, 2021 aver cuando largan algun amp nuevo jeje 1 Quote Link to comment Share on other sites More sharing options...
rockdriguez Posted September 21, 2021 Share Posted September 21, 2021 hace 57 minutos, NICOMORDOR dijo: aver cuando largan algun amp nuevo jeje Lo que necesito el Fuzz Factory!!! salgo al ruedo con lo que trae, meto un eq al final para darle ese agudito extra. 1 Quote Link to comment Share on other sites More sharing options...
Pablo Posted September 21, 2021 Share Posted September 21, 2021 hay algunso detalles nuevos que estan buenos...por ej, que guarda el preset con la SCENE que vos queres encendida...entonces cada ves que ponse ese preset ya esta la escena esa lista encendida....a mime viene genial por lo menos. 1 Quote Link to comment Share on other sites More sharing options...
rockdriguez Posted September 21, 2021 Share Posted September 21, 2021 hace 4 minutos, Pablo dijo: hay algunso detalles nuevos que estan buenos...por ej, que guarda el preset con la SCENE que vos queres encendida...entonces cada ves que ponse ese preset ya esta la escena esa lista encendida....a mime viene genial por lo menos. Estaba seguro que ya era asi, yo al menos en la gigboard. Quote Link to comment Share on other sites More sharing options...
Pablo Posted September 21, 2021 Share Posted September 21, 2021 (edited) hace 9 minutos, rockdriguez dijo: Estaba seguro que ya era asi, yo al menos en la gigboard. en al MX5 no, aparaecias en el preset con los pedales prendidos o apagados segun guardaste, pero no justamente una SCENE prendida. Edited September 21, 2021 by Pablo Quote Link to comment Share on other sites More sharing options...
GabrielLeo Posted September 21, 2021 Share Posted September 21, 2021 Apenas vi el comunicado de Headrush la actualice sin ningun incoveniente ... Todo muy rapido con la Mx5 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.